Mitsubishi EVO X Fuel

Do you have a dual pump setup in your Evo X and wish you had a good way of triggering the secondary pump? Traditionally, people have used a hobbs switch for this purpose, and while it works, they can be unreliable and a bit clunky. It will often require another bung welded into the intercooler piping, extra wires and hoses running through the engine bay, and it's just not as tidy as most people would like it to be.

We teamed up with ripnet and came up with a great new solution. This kit allows tuners to trigger a secondary fuel pump based on load using ECUFlash. The kit includes a plug and play connector and a software patch for your ECUFlash ROM.

Requirements:

• Must use a supported ROM ID. The supported IDs are listed below.
• The car must run a 3 port boost control solenoid connected to the brown connector.
• The factory 2-port solenoid which uses the black connector must be unplugged.
• The car must be an Evo X, this specific kit will not work on a Ralliart
• A secondary fuel pump must be installed and wired up with a relay. The secondary pump should not automatically run when the car is started.

Here's how it works:

1. Plug the provided cable into the black connector which was originally connected to the black 2-port boost control solenoid.
2. Run the wires through the car to the relay which controls the secondary fuel pump.
3. Connect the blue wire to 86 on the relay and the red wire to 85.
4. Go to this website and generate a license key with the coupon code that you were provided. Note that this will require your VIN number.
5. Download the appropriate XML for your ROMID here.
6. Open the downloaded file in a text editor such as notepad.
7. Select all of text in the file by pressing CTRL+A, and copy it by pressing CTRL+C
8. In a text editor, open the XML file that matches your ROMID in following folder (note: this may require Administrator permissions on your PC): "C:\Program Files (x86)\OpenECU\ECUFlash\rommetadata\mitsubishi\evo"
9. Before the "</rom>" closing tag in the end of the file, paste the text from the downloaded file by pressing CTRL+V
10. Save the file. If the file won't save, be sure your have Administrator rights to that folder.
    
11. Launch ECUFlash and open your ROM file.
12. Scroll down until you see "Secondary Fuel Pump"
13. Open "Secondary Fuel Pump - Data", and press the "+" sign to make it say "Data Present".
14. Open "Secondary Fuel Pump - Function Call", and press the "+" sign to make it say "Data Present".
15. Open " Secondary Fuel Pump - License Key" and enter the License Key that you generated.
16. (Optional) Open "Secondary Fuel Pump - Intercooler Sprayer Enabled" and use the "+" and "-" keys to toggle whether or not you want that feature enabled. This will trigger the intercooler sprayer light on your dashboard to turn on when the secondary pump is being fired.
17. Open "Secondary Fuel Pump - Load vs RPM" - Set the load points for when you would like the secondary pump enabled at various RPMs.
18. Open "Secondary Fuel Pump - Load Hysteresis" to edit the hysteresis of the trigger.

Currently Supported ROM IDs:

• 52680022 (GSR 08-09)
• 56890013 (GSR 2011)
• 59580004 (GSR 13/15/FE)
  

Note: These will work with the Tephramod v1-3 versions of these ROMs (i.e. replacing the third to last number from 0 to 1, 2 or 3). For example, the Tephramod v3 ROM ID 52680322 will work the same as the standard ROM 52680022.

ROM IDs Currently in Development:

• 52690022 (MR 08-09)
• 55570006 (GSR 2010)
• 55580006 (MR 2010)
• 58010005 (GSR 2012)
  

Other ROMs can be added upon request.

Mitsubishi Evo X Injector Set: 4x650cc Super FAST Lightweight Custom Modified Saturated / High Impedance Ball & Seat Injectors. Includes pigtails PGT USC4 or add Plug & Play adaptors.

Mitsubishi Evo X Injector Set: 4x775cc Super FAST Lightweight Custom Modified Saturated / High Impedance Ball & Seat Injectors. Includes pigtails PGT USC4 or add Plug & Play adaptors PADPUtoD4

Mitsubishi Evo X Injector Set: 4x1000cc Super FAST Lightweight Custom Modified Saturated / High Impedance Ball & Seat Injectors. Includes pigtails PGT USC4 or add Plug & Play adaptors PADPUtoD4

The Fuel Injector Clinic 1200cc Injector is a saturated / High Impedance Ball & Seat Injector. This 1200cc fuel injector provides great trailing throttle response and minimum pulse widths resulting in a perfect cold start and idle. And, it will work with E85 or other high performance fuels.

Mitsubishi Evo X Fuel Injector Clinic Injector Set: 4x1200cc Saturated / High Impedance Ball & Seat Injectors. Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Includes pigtails PGTJETR4Q or add Plug &Play adaptors PADPJtoD4. PREVIOUSLY IS127-1100H.

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

Fuel tank rusted? Are the studs broken to your fuel pump hanger? Replace it with this OEM Fuel Tank for the Evo X.

Note: Requires additional freight shipping to be paid separately.

Fuel Injector Clinic’s 1650cc/min high impedance injector is the largest high impedance injector compatible with all race fuels and has excellent idle performance in street driven cars while still providing enough fuel to support higher horsepower output on both E85 and gasoline.

The 1650cc high impedance injector can be used with any fuel type based on the stainless alloy valve construction. It is compatible with pump gasoline, E85, Q16, VP Import, FTW and other MTBE oxygenated race fuels!

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 120ºF (49°C) fuel temperature using 93 Octane, 10% E pump gasoline.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

The newest addition to our product line is the largest high impedance injector ever by a long shot and will work for most of the guys running E85 or other high volume fuel. (DO NOT USE WITH "Q" or OTHER OXYGENATED FUELS.) Not only is it BIG, it provides a near perfect idle!

While this injector is not inexpensive, it provides single injector solutions when twin rails would otherwise be needed and there are additional savings in DYNO/TUNING costs due to its easy tuneability. The very linear performance of this injector, based on Bosch’s latest technology, makes tuning a breeze. This is the ultimate solution for all cars that come with high impedance injectors.

Important note: These fuel injectors are high impedance and do not require the use of a resistor box. If the vehicle in which this product will be used came with a resistor box from the factory (DSM / Evo / Etc.) you will need to remove that resistor box for these to function properly! Please feel free to contact us with any questions or concerns.

Supersedes  PN 227-2150